Logotipo Texsa, S.A.

MORTERPLAS SBS FM 3 KG

MORTERPLAS SBS FM 3 Kg is a waterproofing membrane, made of SBS elastomeric bitumen, reinforced with polyester felt (FP), and finished with a thermally bonded film on both the upper and lower side.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
· The SBS elastomeric mastic provides the membrane with excellent flexibility at low temperatures.
· The non-woven polyester felt (FP) reinforcement on the inside and the polyester felt on the upper surface confer the best mechanical properties to the membrane:
· Maximum traction and puncturing resistance (static and dynamic).
· High tear resistance.
· Good dimensional stability.
· Application with mechanical fixing offers the following advantages:
· Fast installation.
· Installation is not as affected by the possibility of bad weather.
· Since the membrane is not adhered, it allows for potential movement of the support.
· Non-trafficable roofs without heavy protection: double-layer application as the bottom membrane of a system installed with mechanical fixing. This application is especially recommended for Deck roofs and restoration.
· Trafficable or non-trafficable roofs with heavy protection: adhered application, floating or with mechanical fixing made up of double-layer membranes. The two membranes will always be adhered to each other.
· SUPPORT: The surface must be dry, firm, even, clean and free of loose materials.
· When waterproofing metal roofs, it is recommended that you install the fretwork sheet with the greatest surface area on the upper side, in order to allow installation of the insulation and the membrane.
· The membranes are installed in such a way that no more than three membranes overlap at the same point.
· Overlaps are carried out with flame, with a minimum longitudinal overlap and a minimum transversal overlap of 10 cm, first eliminating the polyester felt from the surface with flame and with the help of a trowel to ensure mastic adherence.
· The top membrane must be completely adhered to the bottom membrane, and it must be placed in the same direction and so that the overlap lays approximately in the middle of the bottom membrane.
· We recommend using mechanical fixings with washers with a minimum surface area of 1600 mm2, with a maximum diameter of 5 cm for circular fixings and widths no greater than 4 cm for rectangular fixings. Fixings must have a resistance to static extraction equal to or greater than 1250 N. See Annex 2 of the DIT No. 06/0018, where a series of fixings that meets requirements is listed. The site’s wind load, environmental conditions, and local standards must be taken into account with the calculations.
· Installation and measurements will be conducted in accordance with regulations of the UNE 104401 standard.
Roll: 1 m x 13 m
Pallet: 351 m²
· In accordance with the EN 13707 standard. Certified with CE marking No. 0099/CPD/A85/0087
· Voluntary certification of the product with AENOR seal according to the same European standard.
· With DIT No. 06/0018 MORTERPLAS SBS FM DOUBLE-LAYER and ETAG 006
· Quality System in accordance with ISO:9001

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com