Logotipo Texsa, S.A.


MOPLY N FP 3 KG is a non-self-protected membrane, made of APP plastomeric bitumen with polymer additives, with low temperature plegability of ≥ -10 ºC, reinforced with polyester felt (FP), and finished with a thermally bonded film on both the upper and lower side.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations
· In the system, it improves the features of the primary membrane in terms of resistance to traction, puncturing, static and dynamic, especially if the primary membrane is reinforced with Polyethylene PE (polyolefins) PE or fibre glass felt FV.
· Replaces the oxyasphalt membrane by providing a less contaminating production process and results in:
- A mastic with plastic features that allow for easy placement and handling.
- Better performance at high temperatures and better flexibility (-10ºC), provides the membrane with a slower ageing process.
· The non-woven, punctured and stable polyester felt (FP)
reinforcement, confers the best mechanical properties to the
- High tensile strength
- Maximum puncturing resistance (static and dynamic)
- Great tear resistance
- Good dimensional stability.
· Base membrane in multi-layer waterproofing with a membrane equal to or greater than 3 kg from the MOPLY N PLUS line.
· Application as a complementary membrane in single-layer trafficable or non-trafficable systems with heavy protection used with a primary membrane equal to or greater than 4 kg from the MORTERPLAS or MORTERPLAS SBS line.
· This is a complementary membrane for self-protected roof systems used with a primary membrane from the MORTERPLAS MIN or MORTERPLAS SBS MIN line.
· As complementary membranes in green roof systems used with a MORTERPLAS GARDEN MIN primary membrane or a double-layer membrane made of membranes whose top MORTERPLAS FP 4kg GARDEN membrane has anti-root protection.
· As an emergency or auxiliary membrane when provisional waterproofing may be required.
· As a complementary reinforcement membrane for a single or double-layer solution on specific areas of the roof, such as transit areas or machine areas.
· Waterproofing of foundations, basements, etc.
· As a vapour barrier in conventional roofs.
· SUPPORT: The surface must be dry, firm, even, clean and free of loose materials.
· It can be applied completely adhered, partially adhered or floating.
· To adhere the membrane to the support, the support is primed with EMUFAL I or EMUFAL L. Once dry, use flame to adhere the membrane.
· The flame is applied as uniformly as possible (the greater the heat, the greater the retraction) along the width of the membrane without reaching the overlap, which will be done later, since it is important that the temperature be the same in every area. The flame should be applied until the anti-adherent film pore opens.
· The membranes are installed in such a way that no more than three membranes overlap at the same point.
· Overlaps are flame-bonded, with a minimum overlap of 8 cm.
· The top membrane must be completely adhered to the bottom membrane, and it must be placed in the same direction and so that the overlap lays approximately in the middle of the bottom membrane.
· Installation and measurements will be conducted in accordance with european regulations and the Texsa application guide.
Roll: 1 m x 13 m
Pallet: 351 m²
· In accordance with the EN 13707 standard. Certified with CE marking No. 0099/CPD/A85/0087
· Voluntary certification of the product with AENOR seal according to the same European standard.
· Quality System in accordance with ISO:9001




In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.


C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com