Logotipo Texsa, S.A.

TEXSELF BAND AL natural 1,5 mm a 15 cm

TEXSELF BAND AL natural 1.5 mm is a self-adhesive waterproofing band made up of an elastomeric mastic (SBS), coated on the upper side with a sheet of embossed aluminum and on the lower side with a easily remove silicone film.

Technical documentation

  • Logo Facebook
  • Logo Twitter
  • Logo Linkedin
  • Advantages
  • Application
  • Installation
  • Storage
  • Regulations

· TEXSELF BAND AL natural 1.5 mm is a non-reinforced band on which the upper finishing acts as reinforcement and anti-adherent at the same time. The finishing is a 50 micron sheet of embossed aluminium.
· Extremely simple application: applies quickly, cleanly, and without the need for additional tools.
· Easy adherence to the substrate after applying the asphalt primer.
· Overlaps are carried out by simple contact and pressure.
· No blowtorch needed; TEXSELF BAND AL natural 1.5 mm application only requires a brush, cutter and rubber roller.
· Safe to install; minimal risk of fires because no flame is used.

· Restoration of aluminium roofs
· Repairs and sealing of aluminium roofs
· Repairs and strengthening waterproofing on roofs.
· Strengthening of chimneys, pipes and, in general, building materials that are susceptible to filtrations.
· Sealing of joints and overlaps.
· Duct and downpipe joints.
· Repairs and sealing of fibre cement roofs.
· As corrosion-protection for building materials: bricks, concrete, metal.
· Detail resolution: wall joints, ridge caps, chimneys, skylights, etc...

· SUPPORT: The surface where it will be applied must be free of dust, loose or poorly adhered materials, oily or non-stick residue and any soil in general. It may be applied on concrete, wood and fretwork sheet supports; an adherence test must be conducted on all other surfaces.
· Primer: For better adherence of the membrane, apply EMUFAL I to the support, allowing to dry completely, approximately 24 hours. For flat and cohesive surfaces: metal, plastic, solid wood surfaces, priming may not be necessary. We recommend conducting a test beforehand in order to verify adherence.
· Remove the non-stick silicone film from the lower side and apply the membrane to the previously primed surface.
· Press the membrane against the substrate with a brush, from the center toward the edges, in order to prevent bubbles from forming.
· The overlap will be at least 7 cm, and will be carried out by pressing firmly (once the silicone film is removed) on the upper membrane with a roller.
· TEXSELF BAND AL NATURAL 1.5 must not be applied when temperature is below 7ºC. If cold, windy, or humid, heat lightly.
· Installation and measurements will be conducted in accordance with regulations of the UNE 104400-3 standard.
Roll: 15 cm x 12 m
Box: 48 ml
· In accordance with the EN 13859-2 standard. Certified with CE marking No. 0099/CPD/A85/0005
· Quality System in accordance with ISO:9001

Related Systems

 

DATA PROTECTION

 

In cases where the user must provide data of a personal nature to TEXSA SYSTEMS SLU to use any of the Web services, the former will be expressly informed each time of the existence of an automated data base, the aim of same, those receiving the information and identity and address of the person responsible for data treatment, all with the aim of complying with that stipulated in Organic Law 15/1999 of 13th December, for the Protection of Data of a Personal Nature. To this effect, TEXSA SYSTEMS SLU shall reserve confidentiality of the data obtained and the users can exercise all rights to access, amendment, cancellation and any others referred to in aforementioned Organic Law 15/1999.

TEXSA SYSTEMS SLU has adopted all the necessary measures of a technical and organisational nature, to guarantee the security of the data of a personal nature, with the aim of preventing their alteration, loss, treatment or unauthorised access, in accordance with the requirements and conditions called for by Royal Decree 994/1999 of 11th June, in which the Regulation of safety measures of automated files containing data of a personal nature, is passed, notwithstanding the user's acceptance and knowledge that to date totally impregnable safety measures do not exist.

In case of doubt or the need to extend the information covering any of the above items, please do not hesitate to contact TEXSA SYSTEMS SLU.

 

TEXSA SYSTEMS SLU.
C/Ferro Nº7,
Polígono Industrial Can Pelegrí,
Castellbisbal
08755, Barcelona - Spain
NIF B66067687

Tel. (+34) 93 635 14 00
Fax (+34) 93 635 14 80

Email:  lopd@texsa.com